.. SPDX-License-Identifier: GPL-2.0 ============================= Kernel driver i2c-imc-skylake ============================= Supported adapters: * Intel Skylake-X / Cascade Lake-X integrated memory controller (iMC) SMBus engine, PCU function 8086:2085 (socket LGA 2066, platform X299) Author: Simone Chifari Description ----------- The integrated memory controller of Intel Skylake-X and Cascade Lake-X processors contains an SMBus engine wired to the DDR4 DIMMs. It reaches the SPD EEPROMs (0x50-0x57) and the thermal sensors (TSOD, 0x18-0x1f) of the installed modules, plus whatever else a particular module carries on those lines. The engine has two independent channels. DIMM slots 1 and 2 are on channel 0, slots 3 and 4 on channel 1, so the driver registers two i2c adapters:: $ i2cdetect -l | grep iMC i2c-6 smbus iMC SMBus Skylake-X channel 0 SMBus adapter i2c-7 smbus iMC SMBus Skylake-X channel 1 SMBus adapter Both channels share one hardware engine, so the driver serializes every transaction across both adapters. This driver is not enabled by default ------------------------------------- The SMBus engine has no arbitration mechanism. System Management Mode, a BMC, and the memory controller's own closed-loop thermal throttling (CLTT) can all drive the same registers, and nothing in the PCI ID tells the driver whether any of them is doing so on a given system. Two masters using the engine at the same time can send a transaction to the wrong address or return the wrong data. The driver therefore refuses to bind unless the operator opts in:: modprobe i2c-imc-skylake allow_unsafe_access=1 Do this only on a system where concurrent firmware access has been excluded. Desktop and HEDT boards have no BMC, but CLTT may still be enabled by the firmware. The driver reduces, but cannot remove, the risk. At probe it reads SMBCNTL on every iMC channel function (device 10 and 12, function 0; offsets 0xe88 and 0xe98, documented in the Intel Xeon Processor Scalable Family datasheet volume 2, reference 614073, section 3.1.9). ``SMB_TSOD_POLL_EN`` in that register says whether the memory controller is polling the DIMM thermal sensors on its own, which Intel documents as mutually exclusive with SPD command access. If the bit is set on any channel the driver refuses to bind: the engine is not ours to drive. This covers the memory controller, not SMM or a BMC, which remain the reason for the opt-in. Per transfer: * every transaction waits for both channels to report idle before it touches any register; * the previous command state of both channels is saved, the TSOD-active state is cleared for the duration of the transfer, and both are restored afterwards; * after each transfer the command registers are compared against what the driver left in them. A difference means another master used the engine, and the transfer is failed with ``-EAGAIN`` rather than reported as successful. The last check is what makes an unarbitrated system detectable: if the log shows ``chN command changed under us (...): another master is using the engine`` then firmware is using the engine and the driver should not be loaded on that system. Config space access ------------------- The engine's registers live at config space offsets 0x9C-0xB8 of the PCU function and are reached with the ordinary ``pci_read_config_dword()`` and ``pci_write_config_dword()``. Nothing special is required. Supported transactions ---------------------- The driver implements SMBus Read/Write Byte Data and Read/Write Word Data. That is enough for ``jc42`` (TSOD), which asks for exactly those two. It is **not** enough for ``ee1004``: both of its accepted combinations include ``I2C_FUNC_SMBUS_BYTE``, which this adapter does not implement, so the driver probe fails with ``-EPFNOSUPPORT``. SPD bytes are still readable directly with ``i2cget``. Implementing SMBus Receive Byte would make ``ee1004`` and ``decode-dimms`` work; it is the most useful thing still missing. SMBus Quick and Receive Byte are not implemented, so ``i2cdetect`` cannot scan these buses. Address a device directly instead, for example SPD byte 2 of the EEPROM at 0x50:: $ i2cget -y 6 0x50 0x02 0x0c Block transfers are not implemented. The engine has block primitives, but no device on this bus needs them. Word transfers use the standard SMBus byte order, so ``jc42`` reading through ``i2c_smbus_read_word_swapped()`` gets the value it expects. Instantiating clients --------------------- The adapter does not create clients by itself. There is no firmware description of these buses and the driver does not scan. ``jc42`` can be instantiated where a thermal sensor is populated:: # echo jc42 0x18 > /sys/bus/i2c/devices/i2c-6/new_device Whether one is populated is visible in ``SMBCNTL.TSOD_PRESENT``; on the development system that mask is empty and no ``jc42`` binds. ``ee1004`` will not bind for the reason given above. Read SPD bytes directly instead. Module parameters ----------------- allow_unsafe_access Bool, read-only after load, defaults to false. The driver does not bind unless this is set. See the section above.